Fuji Spray SoloTAN 3575 Setup: Step-by-Step Guide
By Spray & Sun | Published: 2026-10-14
Category: How-to Guides
Get your Fuji Spray SoloTAN 3575 running with this step-by-step setup guide. Learn turbine placement, FT-5 applicator use, and first-tan tips for beginners.
Quick answer
Set up your Fuji Spray SoloTAN 3575 by placing the turbine on a stable surface, connecting the hose to both the turbine and the FT-5 applicator, then filling the cup with solution and testing the spray pattern on a paper towel before your first tan. Always run the turbine for one minute after each session to clear the hose.
Unbox and position the turbine
The SoloTAN 3575 is designed for home, personal, and light mobile use. Its curved silhouette is compact, but it still needs clearance for airflow. Place the turbine on a flat, stable surface at least six inches from walls or curtains. Avoid setting it on carpet, which can block the intake and cause overheating. If you are mobile, secure the turbine in a case or tray so it does not tip during transport.
Connect the hose and FT-5 applicator
Push the hose firmly onto the turbine outlet until it clicks or seats fully. At the other end, attach the FT-5 applicator by twisting the connector until snug. Do not overtighten, as this can damage the threads. Check that the fluid nozzle and air cap are clean and seated correctly before you add solution.
Fill the cup and test the spray
Pour your spray tan solution into the applicator cup, filling it no more than two-thirds full to prevent spills. Screw the cup onto the applicator and turn the turbine on. Hold the applicator about six to eight inches from a paper towel and pull the trigger. You want a fine, even mist, not a splatter. If the pattern is uneven, adjust the fluid control knob or clean the nozzle.
Setup steps with common mistakes
- Position the turbine: Place on a hard, flat surface with at least six inches of clearance on all sides. Keep it away from curtains, carpets, and other airflow blockers. Checkpoint: The turbine should sit stable and not wobble when you turn it on.
- Attach the hose: Push the hose onto the turbine outlet until it seats fully, then connect the other end to the FT-5 applicator and twist until snug. Do not force it. Common mistake: Leaving a gap at either connection causes weak airflow and uneven spray.
- Prepare the applicator: Check that the fluid nozzle and air cap are clean and properly seated. Fill the cup no more than two-thirds full with solution. Checkpoint: A clean nozzle and correct fill level prevent spitting and drips.
- Test the spray pattern: Turn on the turbine, hold the applicator six to eight inches from a paper towel, and pull the trigger. Adjust the fluid control knob until you get a fine, even mist. Common mistake: Skipping the test leads to blotchy tans. Always test before spraying a client.
- Spray your first tan: Work in overlapping passes, keeping the applicator moving. Start at the legs and move upward. Maintain a consistent distance and trigger control. Checkpoint: If the solution runs, you are too close or moving too slowly.
- Clean the system: After each session, run clean water through the applicator, then run the turbine for one minute with the cup empty to clear the hose. Wipe down the applicator and turbine. Common mistake: Leaving solution in the hose clogs the system and shortens its life.
Product facts
- Fuji Spray Sunless SoloTAN 3575 with FT-5 Applicator: The Fuji Spray SoloTAN 3575 with FT-5 Applicator is designed for home, personal, and light mobile use, and features a curved silhouette. This makes it a good fit for beginners or small spaces, but not for high-volume salon back-to-back sessions.
- MineTan Starter Tan Handy Spray Tan Kit: The MineTan Starter Tan Handy Spray Tan Kit includes the Tan.Handy Spray Tan Machine with Micro-Whirlwind Technology and the Excess 3 Applicator Gun with stainless steel. If you need a more portable, all-in-one option for mobile tanning, this kit is a lightweight alternative to the SoloTAN.
